Leafcarry Hand Forged Damascus Folding Pocket Knife with Damascus Steel Handle Ready for Engraving & Cowhide Leather Sheath | Everyday Carry Collector Gift | RK-375

Most folding knives are steel in the blade and something softer at the grip. The Leafcarry is steel all the way through. Blade and handle are both hand forged Damascus, which makes it heavier in the hand than it looks on screen and gives you a flank of patterned steel down the handle that is ready to take engraving. Open it runs 8.5 inches with a 4 inch blade, and it arrives with the edge already set. Why the profile is ground this way is explained in blade shapes explained.

An all metal folder is not a modern novelty. The pattern welded folding knives that came out of Persia and northern India in the seventeenth and eighteenth centuries were routinely built with steel or watered steel handles, partly for strength and partly because a flat metal flank was the best surface a chaser or a gold inlayer could ask for. The koftgari workshops of Sialkot and Lahore were decorating exactly this kind of surface, cutting a fine cross hatch into the steel and hammering gold wire into it. This knife is not decorated that way, but the reason its handle is left as bare Damascus is the same one: it is a canvas.

Forged and finished in the Czech Republic. It ships with a cowhide leather sheath, protective packaging and a working edge.

Specifications

What a steel handle changes

Put a Damascus handle on a folder and three things move. The first is balance. Wood and bone are light, so a folder with organic scales balances forward, in the blade. Steel scales pull the balance point back towards the pivot and often just behind it, which makes the knife feel calmer to hold and easier to control in fine work, because the mass is under your fingers rather than out ahead of them.

The second is durability. There is nothing to shrink, swell, crack or come loose around a pin. A steel handled folder can be left in a truck through a humid summer and a January cold snap and come out with the same fit it went in with. The third is the surface. Bone and horn can be engraved but they chip and they cannot be re cut. A Damascus flank can take a deep engraving, a monogram, a rune line or a Viking panel, and it holds it permanently. That is why this handle is left bare rather than being polished into a mirror: the pattern is there, and there is room on it.

Why Damascus and not stainless

This is forge welded Damascus, meaning two carbon steels bonded at welding heat and worked down together as one bar. Layers of 1095 give the hardness and edge retention, layers of 15N20 give toughness and the bright band in the pattern, and an acid etch at the end brings the whole thing to the surface. At 58 to 60 HRC it will take and hold an edge that ordinary stainless cannot match.

The honest counterweight is corrosion. Stainless has enough chromium to shrug off neglect; carbon steel does not, and on this knife that applies to the handle as well as the blade because they are the same material. Wipe it dry, keep a film of oil on it, and it will not spot. Leave it wet on a workbench overnight and it will. The two sides are laid out in Damascus versus stainless.

Grip, and how to hold a steel handled folder

The handle is Damascus steel, contoured and sanded so the edges are broken rather than sharp, with a plain steel spine and a jimped flipper tab below the pivot. It is a firmer grip than wood, and in cold weather it will feel colder in the first few seconds before it takes your hand temperature. That is the nature of metal and it settles quickly.

Because there is no organic material anywhere on this knife, there is no oiling of timber or feeding of bone to do. Instead, treat the handle exactly as you treat the blade: a wipe with an oiled cloth after handling, particularly if your hands sweat heavily, because skin salts will etch fingerprints into bare carbon steel over time. A light patina across the handle is normal on a knife that gets carried and does no harm.

Engraving, runes and your own design

Use the rune converter on this page to turn a name, a date or a short phrase into Elder Futhark and we will cut it into the steel or the handle. If you would rather have a Viking pattern than a rune line, choose your own design in the engraving option above the add to cart button and tell us whether it goes on the blade or the handle. Where a piece already carries an engraved design, your chosen engraving replaces it rather than sitting alongside it. This particular knife is built for it, since the handle flank gives more usable engraving area than any other folder in the range. See the engraving page for lettering and layout.

Care and sharpening

Wipe, dry, oil. That is the whole routine and it takes under a minute. Use mineral oil, camellia oil or any food safe light oil, and put a drop into the pivot two or three times a year so the action stays smooth and grit does not build up in the joint.

Sharpening is straightforward. A 1000 grit stone raises a burr and a 3000 removes it; keep the angle that is already on the blade rather than reprofiling. Avoid powered grinders, which can draw the temper out of a thin edge. Do not store the knife inside the leather sheath for long periods, because vegetable tanned leather traps moisture against steel and this knife has more exposed steel than most. Both jobs are covered in steel care and sharpening with a whetstone.

Made in the Czech Republic

This is a handmade piece from the Czech Republic, made in a workshop that still forges, grinds and finishes by hand instead of stamping parts out. The smiths there have kept the older way of working, and the wood, horn and leather are shaped and fitted by hand as well. Two pieces of the same design will never be identical, and that is part of what you are buying.

Ransack Viking is a United States company. We handle the import ourselves, look over every piece when it lands and ship from our warehouse in Chicago, Illinois. Engraving is done in the United States after the piece arrives, so your design goes on before we send it out.

A note on handmade variation

The Leafcarry is hand forged, not machine made and not bulk produced, so the knife that arrives will not be a pixel for pixel copy of the photograph on this page. Because both the blade and the handle carry Damascus, there are two patterned surfaces here and both of them come out of the billet differently every time. Tone, contrast and the way the layers swirl are decided by the hammer and the etch, not by a template.

The dimensions, the steel, the hardness and the build are identical from one piece to the next. The character is not, and on an all Damascus knife that difference is more visible than on any other piece in the catalogue.

Frequently asked questions

Does a steel handle make the knife slippery

Less than people expect. The flanks are contoured rather than flat and the jimped flipper tab gives the index finger somewhere to lock in. Wet hands and heavy gloves are where a textured wood or micarta handle still has the advantage.

Will the handle rust in a pocket

Only if it is neglected. Carbon steel against skin will darken over months into a patina, which is protective rather than damaging. Actual red rust needs standing moisture, and a wipe with an oiled cloth prevents it entirely.

How much engraving will fit on the handle

The flank gives roughly four inches of usable length, which comfortably takes a full name and a date, or a rune line of eight to twelve characters at a readable size. Longer phrases can run across both the handle and the blade.

Is a 4 inch folder too much knife for everyday carry

It is at the upper end. Four inches gives you real cutting capacity and enough handle to grip properly with gloves on, but it is a knife you notice in a pocket. If you want something that disappears, look at the 2.75 inch pieces in the same range.

How does the knife open

Two ways. Press the flipper tab below the pivot with your index finger and the blade swings out, or use the thumb stud on the blade for a slower, more deliberate opening.

When will it arrive

Processing takes one to two weeks because each piece is forged and finished by hand, then shipping inside the US is free. Adding engraving does not usually push it past that window.

What is in the box

• One Leafcarry Damascus folding pocket knife
• Cowhide leather sheath
• Protective packaging
• Care notes for carbon steel
• Forged and finished in the Czech Republic

Explore the range

See the rest of the folding pocket knives, or move up to the Bowie knives and the Viking knives if you want a fixed blade. The material reasoning is written up in the guides.

Worth a look beside this

A near match for this one is the Mosaicfold folding pocket knife. Closest to this in the range is the Hornfold folding pocket knife, pattern welded Damascus. If this one is not quite right, there is the Antlerfold folding pocket knife, pattern welded Damascus.

The Tantostag tanto knife covers the other half of the same kit. Or start from a blank sheet on the custom Damascus knife page.